A see your “new” tank stand’s are looking good:wink:
2 Likes
That’s good to know, brother! There have been soooo many times I’ve wanted to leave it off to increase the juice flow, but just never did…
Thanks! I love that tank and now, I think I’ll love it more!
How much bigger of a wick?
FYI:
I did nothing different to the wick, I just pulled the barrel off and no leaking…
Previously, I couldn’t take full drags off the Billow v2 because the end of the hit would be dry, but now, I can hit it all the way through with no dryness!
EDIT: this just catapulted this tank to a new height!
1 Like
Between you guys, Quitter and Daath I end up buying stuff I had no intention of getting. Now it looks like I’ll be getting a Billow V2 next.
Ok, so my top three are -
Aromamizer RDTA
Goblin Mini
TFV4
3 Likes
Billow v2
Cthulhu v2
Aromamizer
Honorable mentions:
OBS Crius
Goliath v2
TFV4
Mutation X RDTA
1 Like
I stated in the Favorite Tanks thread that
Mine are
Smok TFV4
Ehpro Billow V2
Uwell Crown
However, the only tank I actually have is the TFV4 with the dual deck because the Billow V2 has been taken over by my husband, the Uwell Crown tank is my best friend/roomates favorite tank so I know those are good tanks but they aren’t actually mine! I need some new tanks!
2 Likes
I did that too and no leaking at all and as you say, it wicks a lot better too! Thanks @Pro_Vapes, you’re a champ! 
4 Likes
Yep… it wicks like champ now. I’m going try my favorite build with 22g Ti now that I have more deck space.
4 Likes
I just rebuild it two days ago but I’m gonna rip that up and put a different build in. More space 
2 Likes
i’ll be rebuilding mine as well when i get home…i’ll post my build…lemme know how yours goes!
wow…its like we all got brand new tanks, huh? lol
3 Likes
I just finished my rebuild and it’s a much better vape with 22g Ti and still no leaks.
Use a fluffy wick that rest on top of the juice channels.
It wicks so much better that it feeds these contact coils with no problems. It also have better airflow.
22g Ti contact coils, 2.5mm ID at .08 ohms. It feels like a new tank.
3 Likes
hell to the yeah!
so you upped the gauge to 22, but youre sticking to the 2.5 ID? you dont think it’ll take a 3mm ID?
and 7 wraps, huh? is that maxed out?
i’m pretty excited about rebuilding it…i have 2 auth. Billow v2 and one clone…woo hoo!
1 Like
I wanted to make sure they would fit. I also wanted to build below .1 ohms. 7 wraps Ti contact coils with a 3mm ID might go above .1 ohm. I could only get a few wraps of 22g before with a 2mm ID and it was too low. This is my first try… I will optimize it later. Right now it’s a lot of Ti and more flavor than before.
3 Likes
I tried that first but it didn’t fit so I went with 2.5.
2 Likes
What gauge and how many wraps, spaced or contact.
I guess I went a bit overboard, 4 strands of 28 gauge twisted, 4 wraps spaced.
At least you went for the gusto. You never know until you try. This is the easiest modding I’ve ever done to a tank. It already had good flavor… now it’s great.
2 Likes
I want to replace the screws on my Billow v2…any suggestions?