Hadron Pro replacement lipo

Hey all,
My Hadron Pro’s lipo battery is out and I need a replacement. Has anyone replaced theirs and can recommend one?

I can’t find the FullyMax 4s 30C 1600mAh that came with it in stock anywhere in the U.S. and there are so many different options I don’t know what will fit.

If you can help a brother out, I’d appreciate it.

Thanks in advance.

4 Likes

Looks like there’s spec’s and 2 alternates in the manual ?

. This is direct from the manual, 1600mah 30c 4s(23.68wh)  88.5mmX 36mmX 28.5mm.

At the top of that same page it shows 2 alternate batteries. You can check if their dimensions differ. Depending on how you treat your Lipo’s they can start to swell and you want a little wiggle room in there (which the doors provide).

3 Likes

@Lostmarbles

https://www.vaporwith.com/steam-crave-fullymax-4s-li-po-battery-pack

4 Likes

Thanks D-Man!

2 Likes

I don’t know about this site. They have no info on the “about us” link and their lack of info seems sketchy. Have you ever ordered from them?
I was hoping someone has found a suitable battery that is not the FullyMax 4s. They seem impossible to find and I don’t know enough about Lipos to find a reputable brand with the dimensions.

2 Likes

@Lostmarbles no, I don’t know them, and haven’t ordered from them. Very slim pickings for the exact battery model. Maybe a comparable one instead ?

2 Likes

Yeah. Looks like FullyMax made the battery custom for the Hadron Pro. Doesn’t look like it’s available in the US. Finding another battery according to spec and physical dimension, is proving difficult. I did find one (Turnigy) on eBay that was listed on the Hadron manual, and a buyer mentioned that it fit his Hadron, so I ordered it. Hopefully it does, otherwise imma be pissed.

2 Likes

In case anyone else is looking for one. I cannot confirm this will work as I haven’t received it yet, but it is listed on SC Hadron Pro manual.

2 Likes

Hobbyking has a helper tool for LiPo sizing. And IIRC yours has an XT60 connector soldered on the board end, like it shows on the turnigy you posted. You can also use LiHV (they’re somewhat harder to find) those charge to 4.35V per cell, but the board limits the charging to 4.2V per cell. Some of these China podmods are using LiHV cells inside (just sayin).

3 Likes

i HAD to use aliexpress to buy a LIPO battery for my wireless headphones

it was a terrible experience though trying to find one with the right dimensions
although a slightly smaller one should work too

4 Likes

So I got the lipo and it fits - barely. It’s a really tight fit and you have to mess with how the wires fit. The side panels don’t fit as snug as they should but I use the leather case for it so I’m not worried about them falling off. Good thing its too big to leave the house.
I think Steam Crave may have screwed the pooch a little with the design of this. if it had a more squared off design instead of the sloped panels, it would have been easier to find a battery that would be a better fit.
Someone asked if I wanted to sell it. I just may do that. I hate hassles. Even small ones.

3 Likes

Sorry to hear that you’re having trouble with the battery. Ive stayed away from built in batteries ever since my first sub ohm mod I ever bought. I had a smok stik Prince. I guess it was kind of like a mech mod? I know it’s definitely not, I only say that because I was the battery began to die just wouldn’t hit right anymore. I began to notice it just wasn’t giving flavor no matter what. Turned out to be the internal battery was just dying. Just sucks for a vape to become a paperweight when the battery goes.

2 Likes

You could shorten both ends if you wanted.

These are easily replaced. 2 keyed connectors so you can’t mess up how they plug in.

3 Likes

Good to know, but that thing is long gone lol. Bought it back in 2017 I think. Got rid of it years ago.

2 Likes

I have a newer innokin mod with an internal battery. It’s tiny, yet inside is standard 18650, just like my Philips razor. When they die, it’ll be a quick solder job to replace those.

3 Likes