Lostmarble's Geekvape Loop RDA review

Hardware Reviews
14

What did Cosmic do? :rofl:

5 Likes
15

Nice review bro. I have been curios about this one, so thanks for that.

I was gonna say the same thing. I guess great minds think alike eh? :sunglasses:

I sure would like to see the hole you were talking about. The one that juice drops into ( if dripped ) before falling into the airflow. If you don’t mind that is…

3 Likes
16

Up until one goes all wonky and gives credit to the wrong person… :roll_eyes: /facepalm :laughing:

3 Likes
17

Thanx for the review!
There’s a name for reg 22ga Ti?

2 Likes
18

oh ya, I wanted to know about that too.

2 Likes
19

Not really. It’s just a term PV coined.

2 Likes
20

Are these standard size? Could you use spare grub screws from another RDA?
I really love hex screws as well, then philips screws and lastly flat screws. There should be a law against them :laughing:

2 Likes
21

Thanks Ogre, and yeah…flavor! Haven’t put it down since it arrived yesterday.

1 Like
22

No worries. I used to forget my ex’ name and introduce her as “honey”.

After I botched the first coil, I laid the second one down as I was looking for the cutters and noticed how the legs laid across the flat and tried it out. The coil sat a little lower than what Geekvape illustrated, but it worked out well.

1 Like
23

Thanks brother! I’ll see if I can get a pic of those for you. It’s hard because this thing is really polished and hard to photograph with proper shadows and such. When you drip your juice in it hits the tip of the W and runs down the side. On the side are two holes. One on the side that allows air into the base and one directly below that opens up into the juice well. The side inlet is angled downward so it’s difficult to have juice run out of it.

image
image.jpg1200×620 126 KB

Doesn’t quite illustrate what I’m talking about but may help. There are holes just below the downward peaks for juice to flow into the well. The air also gets drawn down into the well and then gets sucked up through the same hole hitting the coil on it’s way up.

2 Likes
24

Thank you! I’ve been calling it that since I read @Pro_Vapes post way back when.

2 Likes
25

I don’t know. I’ll have to check on that, but I can say that this is very well machined. Even the screws seem better quality than most. It doesn’t look like GV cut any corners on this.

2 Likes
26

That picture screams flavor workhorse to me.

1 Like
27

It does and it is. Give it a try, you won’t be disappointed. I wanted to try some SS wire but I’m loving the Ti coils too much right now.

28

Awesome review @Lostmarbles :ok_hand: it’s a good RDA for sure and you nailed it :wink: nice job, thanks for sharing it with us :+1:

1 Like
29

Praise from the master! Many thanks for taking the time!

1 Like
30

Oh please…

I only answer to superstar genius these days…

please don’t belittle me…

201312_22285f005

2 Likes
31

Sorry your highness. :rofl:

3 Likes
32

Thank you VM @Sprkslfly, and a fine review @Lostmarbles! @Lolly next time hush, i needed the extra recognition :smiley:
I’m thinking I don’t like those tiny hex grub screws and like the slot or philips more so that is a plus for me. But for me I would be more interested in this one if it had a single coil option. And I do Like the juice well, and the top cap/vents and the way that locks in.
Just about a week out now till payday, then i’ll be even more interested…

4 Likes
33

Just got mine in yesterday and frigging loving it! I feel like I’m cheating on my Goon, but that flavor is just so damn nice. Thanks @Lostmarbles! I have to get my write up done soon but ya nailed everything about it. :blush:

4 Likes