What ohms for my new RDA's?

I have a couple new RDA’s but the destructions don’t say what ohm the coils should be used.

1 is a Hellvape Dead Rabbit Pro, and the other is a Vaperz Cloud ASGA20.

A professional Dead Rabbit? What? If it dies, she pregnant. Get the hell outta dodge! Even an amateur can tell ya that!

What’s the difference between ohms? .15 vs .5 or .9… What wattage is best?

My mod is a Smok Morph 2. You can only GET Smok’s in this town!

2 Likes

Hi Pauly.

Awwwww… OHMS Law… A mystery to most, understood by few.

I run my DR Pro with a single coil @55watts and the coil pulls like .30 -.50 depending how I built it.

For me thats the sweet spot for flavor, no spitting and a decent ramp time. I think it’s a matter of preference bud.

5 Likes

It’s completely personal preference but I think the sweet spot is around 0.45 ohms. I make my coils to the 0.45 ohms or as close as I can get.
With higher resistance coils (hight ohms) you need less power (wattage) , less vapour, I think the majority of liquids taste better at higher ohms, battery’s last longer.
With lower ohms it’s the opposite.
Most people want better flavour and I’ve found that slightly higher ohms are normally best for that.
When you’re coil is fitted and ready to vape start low with the wattage and keep increasing slightly until you can get a good, long (around 2.5 seconds) puff without burning the cotton.,
There are lots of good articles on the internet about the subject.

3 Likes

@PaulyWalnuts as posted above, it will be your personal preference, AND, the limits of your power supply, aka MOD. Some MODS can only fire down to a certain ohm rating. As long as you are using a protected device, have fun, and try them all !!!

Unlike PODS, prebuilts, or “kits” you’re free to use whatever your MOD will fire safely. You’ll find your sweet spot. Just experiment. Don’t sweat the details on the ohms, just find what you LIKE and run with it.

4 Likes

try 3x28+38 (ni80), 5.5 Windings, 3.5 mm ID (should 0.4 Ohm single), best “allrounder”-Coil. Rest is, as said, your personal like. On a regulated mod “forget” ohms, 0.2 could be as tasty as 0.4 or 0.whatever.
At least: you want a coil with much surface and less mass, so its fast and tasty

3 Likes

I don’t run the coils they send in the package but for my dead rabbit pro I run usually point one two- point zero eight in mine. I run high wattage due to the airflow. I use ni80/ni90 quad core aliens usually in that rda. It’s personal preference but my dual coil RDA’s all have coils that range from point two zero-point zero eight. As long as your mod can handle it, which yours can, I believe your mod will fire down to point zero 5 (which I do not recommend that low). Point 9 seems a little high for a dual coil with that much airflow, that’s more for s pod type system. In my opinion, around a point one 5 would be a good starting point.

3 Likes

Something like these? That’s a buck a coil!

3 Likes

@PaulyWalnuts

Yes sir. That’s exactly what you want.

2 Likes

Anyone know where I can get them in a bigger bulk?

And thanks!

1 Like

maybe 3fvape has those

but you can buy packs of 50 or 100 XKFM brand on aliexpress for cheaper.

2 Likes

I’ll check when we get back from our Granddaughters wedding. I bought the pack I found 'cuz I can get it here by 11:00 am. tomorrow.

She’s in St. Louis Il. We have family in Michigan we haven’t seen in almost 25 years, so we’ll be out for 2 weeks.

2 Likes

@PaulyWalnuts

Juat an FYI bud. I change my coil like one a month tops. I change my cotton every other day and clean the coil. EASY dry burns, followed by an easy brushing with a steel brush. Very light btw.

I’ll slow burn the residue off the cold 2/3 times and I’m good to go.

2 Likes