Ok @anon60225325 that is now on my to do list😄
1 Like
@anon60225325
After using the Siren 2 for a couple of days, I am satisfied that this is a worthy addition.
The manufacturing quality is excellent, all threads are smooth as silk.
The satin finish stainless steel is great, no finger prints.
Mouthpiece a bit strange, however I did swap it out with another one, and to be fair there was no difference in taste, it is just different in appearance and mouthfeel. I suppose personal preference.
Building on the deck is super simple, and here I used the included coil as well as popping a SS build in for comparison, and to be honest didn’t notice much difference in flavor.
Wicking was a bit of a challenge, and my first attempts using Muji, resulted in dry hits, I did re-wick twice more but had the same issue. Then I switched to Cotton Bacon and hey presto no more dry hits. Could be that I just wicked it slightly different, who knows? This being a mid tank coil, which is apparently to bring the coil closer to your mouth, does mean it has to be wicked like a RDTA.
I also love the bayonet style top cap, it obviates the potential of flooding.
Now I have never used the original Siren so am not able to compare them, but the vape off this tank is absolutely first class. The flavor is amazing, the draw is as good as any I have used to simulate a cigarette draw, with so many air hole options you are really able to dial it in to your liking.
Would I recommend it? Hell yes.
Is it on a par with my current favorite the Vandy Vape Berserker? I would have to say no. The Berserker is just easier to use, build and wick, it looks better in my opinion, and has the option of either 2ml or 4.5ml with the included tank glass and chimney section.
The flavor is pretty much of a muchness, and it probably comes down to personal choice, and the price point, the Berserker being a tad more expensive.
As always these are my opinions and YMMV
Did I mention, the flavor is amazing 
2 Likes
This is awesome, G-Fog! Thank you for the effort 
One question though; what do you think of the flavor? lol
I think I have to test out your current favorite - oh my, finally able to decide, lmao - and then I can make a qualified decision on whether or not I have to test out your current runner up 
Thanks again!
2 Likes
did I forget to mention it.In my opinion, the absolute best RTA for mouth to lung (as far as taste goes) is the Wotofo Serpent Mini. This little tank works well and the taste is unbelievable. The only downsides to this tank is that it goes through its 2 ML of juice in no time. That’s probably part of the reason the taste is so good. You will defiantly need to carry extra juice if you leave the house. The other issue is that it gets a little wonkie (if that’s a word) when building. If you do not get it right, you will know. It is a t-teetotaler tank for me. If I do not wick it perfectly, dry hits or flooding. Once you get the hang of it, it is outstanding.
My second choice, and the tank I carry most times is the Digiflavor Siren V1. I have not tried the V2, but the V1 is just an awesome tank. Sometimes get a little seepy, but wick it right and this tank has great flavor and is large enough to last a good while. I know there are people that did not like the glass around the build deck. I like it because I can see if the cotton is getting to the point that I need to rebuild the tank.
I’m interested in the
Berserker - https://greyhaze.co.uk/products/berserker-mtl-rta-by-vandy-vape
Ares - Phil Busardo Ares
Siren v2 - https://greyhaze.co.uk/products/siren-v2-mtl-rta-by-geek-vape?variant=207785689097
Cthulu Hastur - http://www.cthulhumod.com/hastur-mtl-rta/
These all look like very similar MTL RTA 's but anyone got any preferences and why?
1 Like
@anon60225325 now to throw the cat among the pigeons.
I just received the Cthulhu Hastur MTL RTA, and we have a new contender.
I’ll see over the next few days, where this tank takes me, but so far I am very impressed.
2 Likes
I like the deck of that one
2 Likes
Noo, you can’t keep doing this! 
Looking forward to hearing your comparisons, G-Fog, thank you for giving my piggy bank a heads up
1 Like
I use the Aspire Nautilus X with 5ml extension most of the time. Uses coils but is really reliable and flavor is ok. I have the Siren 1 and Mark Bugs Gem 2, both which I really like. However I find both have their days of leaking and dribbling and I can’t be dealing with that out and about! Got the Siren 2 on order and seriously considering the Berserker. Will report back on Siren 2 but v excited by it!
2 Likes
Well having spent some time with the Berserker, Siren 2 and the Cthulhu MTL RTA, I have to say that IMHO the Berserker wins on flavour, the Cthulhu on airflow and the Siren on it’s build deck. YMMV of course.
Now that the Innokin Ares is out, maybe it will have the best of all worlds? I’ll know in a few days 
I am having a MTL blow out ATM, vaping heaven.
4 Likes
Would you consider doing a comparison thread of those if you have the time, I’m in the market for one of them but would love to hear more intricate personal thoughts about them.
1 Like
@Grubby Yes I’ll see what I can put together, it will take a bit of time though as I will need to add the Ares to the mix, which should be here in the next couple of days.
Do bear in mind I’m not a reviewer, but I’ll do my best 
2 Likes
Thanks, I wouldn’t expect a long drawn out post with every angle covered, just your opinion of how each performs / differs would be much appreciated. 
Just think @Tworrs you can enter the world of reviewer. You can be a comparison reviewer, a niche that hasn’t been claimed by anyone yet! I say go for it Brother !
2 Likes
I’m not a MTL vaper but I have been considering getting a MTL RTA for my tobacco mixes. I would love to hear your thoughts on how your rtas compare.
1 Like
Thanks @Saxonn the only question being, can I afford the time to do it justice? 
Ive been using both the Siren V1 (for over a year) & the Berserker (for a couple of months) & would gladly share my subjective opinions on each…
The Siren V1 is a stellar vape …except for the airflow- way too airy for a MTL. Someone (sorry, cant remember who) suggested drilling a .08mm hole… yep, that’d fix it! I was planning on doing that but never got around to it - I just stepped it down to 1/3 of the smallest hole. I believe this issue has been sorted with the V2, which IMO would make this tank truly awesome!
The Berserker has tremendous flavor - on a par with the siren, however the airflow is perfect!.. my go-to MTL tank that I use every day. A common complaint with the Berserker is that the deck can be prone to flooding. To get around this, I close the airflow to fill then put the top-cap back on and turn it upside down to reopen the airflow - havent flooded once using this method! An “on-point” vape. My only complaints are that it can get quite hot sometimes & the supplied driptips are rubbish - after my first 3 pulls I had juice in my mouth so out they went. I now use a 17mm PEI driptip from FT
Perfect.
1 Like
,mOK here are my thoughts and experiences of the Cthulhu Hastur MTL RTA, Siren 2 GTA MTL and Berserker MTL RTA.
In an attempt to offer my personal experiences with various MTL devices in a like manner, I have coiled with 28g Kanthal, 2.5mm ID, 8 wrap which comes in at about 1.5ohm, and then wick with Muji organic cotton. All this just to have a comparable baseline from which to compare apples with apples.
Of course, all of this is just my personal opinion, and your experience may well be different.
Any errors are all my fault
Cthulhu Hastur MTL RTA
This is a 22mm MTL RTA with 3.5ml juice capacity, which comes with 5 air flow restrictors, a spare frosted glass, and the usual O-rings and screws.
The build deck is in the middle of the Atty (RDTA style), and accommodates a single coil, with the added advantage of accepting either a clockwise or counter clockwise wrapped coil. The coil posts are side slotted which make the insertion of the coil legs easy, as does the slightly recessed section into which the screws trap the legs. A nice touch which to me made the process really simple and hassle free.
Wicking is easy, just fill the channel with the same amount of cotton that snugly fits through the coil, dangle the wick into the chamber RDTA style, wet up your wicks, assemble and fill through the top section, which is a bayonet type cap release making filling really easy, however there is not stop detent so it can rotate 360 degrees, so caution when fitting is needed. The bayonet top cap stops the build-up of pressure in screw on type top caps, that could force liquid up to the coils causing flooding, which I have not had with this Atty
Great airflow, and easily adjustable, with the included restrictors and the AFC on the base you will have to try different setups till you find your perfect air flow.
I found the AFC very tight and difficult to adjust on the mod, even with some lubrication, but once set (off tank), the AFC stays in place.
I was not able to work on the deck with juice in the tank, which is a negative to me.
The drip tip is not comfortable to use, and I have replaced it with an aftermarket one.
Overall, a very flavourful vape that has great airflow and is easy to build, and I have had no leaking, flooding or gurgling at all.
Tops for airflow.
Digiflavor Siren 2 GTA MTL
A 22mm MTL RTA with 2ml juice capacity, which is a bit sparse for daily use. Comes with the usual accessories, spare glass and a couple of pre-made coils.
The build deck is in the middle of the tank with trailing wicks, RTDA style, along the same lines as the Hastur.
The two posts accept a single coil with top slotted channels, so dropping a coil in is really easy, and then tightened with screws from the side of the posts.
Wicking is again just like a RDTA, snuggly fit wick through the coil and trail the ends down into the tank beneath the deck, making sure the cotton is not trapped in the threads, but ensuring the juice channels are just filled, which obviates any flooding.
Top filling via a bayonet style top cap makes this tank very easy to fill, and as this one has a stop detent inside, unlike the Hastur, there is no chance of turning it too far, and the top cap popping off. Again the bayonet style filler obviates flooding of the coil.
The airflow is controlled by an AFC ring on the base which gives you loads of options, from holes 1-5 or any combination of those. If you want something else the opposite side of the ASFC has a single hole that you can line up with any of the holes noted above individually. So the options are really great. The airflow hits the coil from underneath via 3 small hols spread across the length of the coil, which really enhances the flavour.
Overall a very easy tank to work with, that has truly great flavour, with an absolutely amazing deck to build on.
With the thicker O-ring attaching the glass to the base, I found I could work on the base with the tank section still containing juice, a plus in my eyes.
I have had no gurgling, flooding or leaking.
I personally don’t like the drip tip, it is not comfortable on the lips, and I feel that the added little bit on the top could form a germ trap where it joins the main body of the drip tip.
The juice capacity is too small at 2ml, and you would have to go for the Siren 2 24mm to get more capacity.
Tops for buildability.
Vandy Vape Berserker MTL RTA
A 24mm MTL RTA with the option to have either a 2ml or 4.5ml capacity with the included tank extender sections of glass and chimney. Come with the usual bag of accessories, the tank extenders and a spare drip tip.
A bottom build deck section which is easy to build on, just unscrew the screws and drop the coil in and tighten, no issues were found with thinner wire that I tried. Wicking is dead easy, enough cotton to be snug in the coil, and cut the wick just long enough to touch the bottom of the well, being careful not to block the juice flow holes in the bottom of the well, and fluff it to fill side to side of the well, wet the wick and assemble.
Now here is where I have had some flooding, the top cap is screw on, which seems to create pressure on the juice, forcing it up to the coil. Some people advise to close the airflow, start screwing the top cap on, just a thread or so, then invert the tank and complete screwing the top cap on then open the airflow. Personally, I just don’t fill it to the top, and so far, I have not had further issues.
Note that I only had the flooding issue with the 4.5ml tank extender on, in 2ml format I have had no flooding. Just be aware though.
The airflow enters through a single round hole under the coil, which concentrates the airflow onto the bottom of the coil. The AFC ring has multiple holes, accessed through a single teardrop shaped opening. I have found the 2nd largest hole is best for me.
I have found the AFC ring to be very loose and easy to move inadvertently.
No leaking issues were apparent.
Be aware that if you want to completely disassemble the tank, the screw in the top of the Atty under the top came, loosens counter clockwise, and there is a tool in the kit to use for this purpose.
Overall my experience with this Atty has been very satisfying, the build deck is incredibly easy to work on, even with juice in the tank, thanks to the wide O-ring on the base.
The flavour is outstanding.
Tops for flavour
8 Likes