That high level of freebase is nuts to me. I once took 3 puffs of 25mg and had to sit dowm for 20 minutes.
1 Like
I used that for years, itās very good.
1 Like
@Mediocre_Remedial I used this cotton for a long time and absolutely loved it! Now that my fingers donāt work like they should any longer I have switched to Hellvape shoelace to accommodate my āhand toesā, itās a very good cotton imo but a bit more pricey.
2 Likes
That is crazy. I only use 1.5mg with sub ohm lol
2 Likes
Your innocence is endearing 
4 Likes
Okay, Iāve tried wrapping like seven coils. I canāt for the life of me get them to come out to what this chart shows. That is the coil gauge I bought, in yellow is what itās supposed to be at six wraps at in 3 mm, The red is what I keep getting. .29 ohms was the closest I got, but my coil is six wraps not seven. Iām about to wick this one to see what the flavors like. The other ones I wrapped arenāt complete junk I was just unsatisfied because Iām a perfectionist.
2 Likes
Also, the little screw on the wire jig that wraps the wire around the jig leaves a little line across the coil. Itās dragging on it.
2 Likes
Donāt wind it with the screw. You Ohming out at 0.42?
3 Likes
Iām aiming for .26 ohms at six wraps like it says on the chart. Iām instead getting .30 .32, The one I have in right now is .28 itās a little closer.
2 Likes
yes everyone has had lackin mediocre coils starting out
there is some experimentation to do
You know when you fire the coil to strum it you can instead stick the jig in it and pull and really straighten it out?
3 Likes
My calculator for a quad NI80 28 X 38 6wrap should be 0.261 Ohmās. your close.5wraps should be about 0.22
3 Likes
I just asked AI to make me a picture of a Clapton coil with the text āmediocre_remedials lackināmediocre coilsāā¦
And it gave me a picture of Eric Clapton. 
4 Likes
I got one here thatās reading .28 ohms, as soon as I screw the top of the tank back on it shorts out to .10
Wtf. But I take the tank back off it goes back to normal. Iāve never had this problem before.
never mind found a tiny little wire in the deck
ā¦ Littleā¦
2 Likes
Your advice to not use the screw worked. Iām not sure where the post went or you said that, but now I think this hand wound coil has better flavor. Also .28 ohms, not bad.
2 Likes
The screw is there to wrap before the coil is pre wound. You are using pre wound coils. Just hand wind as tightly as possible If itās loose give it a lite tug with a plyers.
3 Likes
Okay, thank you. The hand wound coil is reading 0.27 now. Even the ones I buy pre-made are a little bit off what it says itās supposed to be.
1 Like
Iāve got just about one last question for right now. Thereās 2 small holes on the jig, if I try to fit this wire through one it kind of gets stuck after Iām done wrapping it. I have just been using this little cutout in holding it with my finger. Is that the correct way to do it?
2 Likes
You can use the slot or hold the wire with a plyers. What ever is more comfortable to you.
3 Likes
āMake my recipes, or Iāll cap your assā
āAll work and no gun makes Pauly boredā
Iāll go With āPaulyās Nutsā. Am I crazy, or are my bollocks impressive?
Hey, if I go with āPaulyās Bollocksā only the Brits will get it.
Ooh, ooh. I got it! Iām going with āPaulyās Coglioneā. Italian slang for testicles! Itās used to call someone an idiot, fool, jerkā¦etc.
.
3 Likes