As per the holes, just pull off the entire top. Once holes are set you will never need to adjust. Pull it right off base. Holes stay the same once set. Did I mention this RDA rocks way better than any tank lol. Just did a test of Aspire Clieto and Goon. Goon produced 3 times at least thicker vapour and the same with flavour and uses minimal ejuice compared to tank
2 Likes
Pull it right off base to expose coils then drip. Not sure you know this but if you do I am just trying to help.
1 Like
I just drip right down the center. Not one issue for months.
2 Likes
You couldn’t have made a much better choice, definitely among the very best RDAs out there.
I run N80 Alien coils, 3mm, 5 wrap, 0.1 Ohm mainly on a mech mod, but if I use a regulated mod I vape at around 110 Watts.
But as previously mentioned, do what works best for you.
As you’ll probably get addicted to buying vape gear, like a lot of us.
I’d recommend the Apocalypse or Skill RDAs as your next purchase.
They’re both as good as the Goon, possibly even slightly better flavor.
3 Likes
Thank you @benjy337 I will look into those RDA’s for sure. Wow, you vape way up there. I keep my watts around 65 still but slight pull of air till I hear coils kick in then vape harder. I’ll crank it up and have a test at 100 again, its too strong up that high for me. lol … Ok, I tested it at 100 and its great but I find flavour fades after 2 or 3 good hits. At 65 ish watts I find I drip less often and still great vapour and flavour production…hmm, its great both ways …I’m liking it !
@Chrispdx …Just tried that drip down the middle … not bad I must say
Still like to take top off once in a while though to paint coils and cotton with juice … I will try this more often as well. Vaping is just too cool, many different methods and all are friggin great . I think I’m getting way too nic ed out man, trying out different wattage settings and drip styles lol.
Vape on!
2 Likes
Once my husband and I bought our Goons, we havent looked back. It is nice to find an atomizer that fully meets your needs. I liked some of my old RDA’s and RTA’s but it always seemed like they had a characteristic flaw for me, such as not enough airflow, or limited build room, or even a pain to wick, but the Goon suits my needs perfectly. It has gotten cheaper not buying vape stuff all the time.
2 Likes
i drip down the middle sometimes, but i squeeze it out of the plastic bottles (don’t have a glass eyedropper style right now ) and tend to overdrip and it spills out the airholes. as for taking the barrel off to drip is tough. the o rings on the bottom are pretty tight. i like to keep mine to the brim with juice. it seems that i get the best flavor that way. sometimes i am not paying attention and put it back on with the single airflow, then i hear the difference in sound and am like what the shit! ive heard complaints about the goon airflow being noisy. it is kinda but it doesn’t bother me at all. as i said i like the juice really full, so the sounds of the juice heating is noisy so the airflow sound is nothing. I’ve been only using this set up for quite a while and have no complaints at all with it. i don’t buy anything else as far as hardware either bc what i use is great to me. …although i do have a SMPL mech mod and another goon boxed up in the closet in case the fda bs really happens. the smpl mod is practically unbreakable unless you run it over with a tank so i think if shit hits the fan that is all i should need
1 Like
I use goon clones daily - 1 on the desk and one for taste testing. both are in SS TC mode. I only ever drip thru the tip. 15 - 20 drips out of a fine tip dripper, then 8 or 10 vapes until the vapor gets weak and re-drip. I can count the times I have over-dripped the past 6 months and had it come out the air holes on one hand. That typically happened first time dripping it for the day and not vaping it first to see if it was ready to be dripped on.
1 Like
Dripping down the center takes some thought. I normally have an incendent once month. Once a week on my volicty v2 clone. And once a day on the tsunami geekvape that I have stopped using. Lol.
1 Like
Fozzy I Drip exactly the same way, in fact when using short 30ml glass bottles, I fill the glass dropper just under halfway, and this is the exact amount I need to not overdrip. That Kindbright Unholy Style RDA looks neat, I have kinda wanted that one.
1 Like
Yep, I use glass drippers in the testing lab and you really can’t overdrip with those if the dual coil wicks are dry and you just squeeze the bulb. If you run a single coil in the goon over-dripping is real easy IME.
I had to give my tsunami away. Nothin’ but over-drips on that thing.
Never over drip when using an EZ Dripper, once you know how many times to squeeze for the particular RDA, you will never over drip. Great holder for the car too.
I highly recommend them, makes dripping so easy.
They just started selling a 30ml version too.
just checked out the ez dripper. seems cool. but why does it have a warning not to use diy juice?
1 Like
The Tsunami was such a pain, and I happened to get the one that leaked through the pin too (was seated off to the side). I really dislike that RDA. Not enough wick room.
No idea, very strange.
There is of course no difference between DIY and any other juice.
I use them with my DIY juice and have never had a problem.
There are certain acidic juices that have been known to crack atomizer tanks, but it’s very rare.
I guess they’re just tying to cover their arse.
1 Like
All bottom airflow RDAs are prone to leaking, that’s why I don’t really use them, even though they produce good flavor.
1 Like
ok guys and gals, one reason I bought this RDA is in fact for the reason that it is made in the U.S.A. Period people. I’m Canadian and I respect this. I lost my job of 26 years working for an American company that thought they could manufacture the same product in Mexico…ummm! Not! Well I’m out of a job at least I can support a New Jersey made product …the Goon. I will and always will support my American people and Canadian manufacturing because we do it right and do it right the first time … no bull shit. P.E.R.I.O.D. Do not settle for second best. Support your own people
2 Likes